While changing oil today, I decided I would also pull the throttle body (TB) to clean it. My truck only had about 18,000 miles on it, but I thought I would check it out anyway to see how dirty it was. Here is the way to do this, if you want to do it. I've heard other members state that by 30,000 miles, the throttle body can be very dirty. Mine was not bad, but I am careful to use a Top Tier fuel and run a can of Sea Foam in the gas every few thousand miles.
1. Disconnect Battery:
This will help by resetting the ECM to accommodate the clean TB, and to ensure you don't accidentally short something out (although this is very unlikely).
2. Remove the Cover/Shroud:
The plastic cover over the engine is attached by 2 "buttons", like little compression fittings. It raises up, then toward the front of the truck to remove.
3. Remove the Intake/resonator:
Unscrew the clamp near the TB, and the one closer to the air cleaner/MAF. Then unattach the small line that runs into the side of the resonator (just twist and pull).
4. Unhook the Electrical Connector:
Slide the small gray retaining clip back and remove. Push down (pinch) the connector, and pull back on the connector to unhook it.
5. Unscrew the Bolts Holding the TB:
There are generally 4 bolts that hold the TB in place. On mine, the top 2 have nuts that are removed, and bottom 2 are bolts. Whatever combination you have, remove the 4 retaining bolts/nuts.
NOTE: There is a gasket behind the TB. Ensure you locate this as you remove the TB. Often, it sticks to one surface or the other.
6: Remove TB:
Carefully remove TB, and set aside. Note the location of the gasket (mine is green). Once removed, cover the area with a clean towel so no dust can enter the opening.
7. Clean the TB:
Use a cleaner made specifically for the throttle body. Spray it from all sides, and allow the cleaner to work for a minute or so. Wipe it clean with an old lint free cloth. If needed, use an old toothbrush to remove all of the build up. NOTE: It is OK to move the butterfly (gently). Be sure to clean every side well. Allow it to dry before reassembly. This is also a good time to clean your MAF sensor: How to Inspect and Clean a Mass Air Flow Sensor (MAF)
8. Put it all back together:
Simply reverse the process. Bolt the TB back on, using a cross pattern (like mounting a tire). Plug in the elctrical connection to the TB. Attach the resonator, and be sure to plug the breather hose back in. Then put the engine cover on, and connect the battery.
1. Disconnect Battery:
This will help by resetting the ECM to accommodate the clean TB, and to ensure you don't accidentally short something out (although this is very unlikely).
2. Remove the Cover/Shroud:
The plastic cover over the engine is attached by 2 "buttons", like little compression fittings. It raises up, then toward the front of the truck to remove.
3. Remove the Intake/resonator:
Unscrew the clamp near the TB, and the one closer to the air cleaner/MAF. Then unattach the small line that runs into the side of the resonator (just twist and pull).
4. Unhook the Electrical Connector:
Slide the small gray retaining clip back and remove. Push down (pinch) the connector, and pull back on the connector to unhook it.
5. Unscrew the Bolts Holding the TB:
There are generally 4 bolts that hold the TB in place. On mine, the top 2 have nuts that are removed, and bottom 2 are bolts. Whatever combination you have, remove the 4 retaining bolts/nuts.
NOTE: There is a gasket behind the TB. Ensure you locate this as you remove the TB. Often, it sticks to one surface or the other.
6: Remove TB:
Carefully remove TB, and set aside. Note the location of the gasket (mine is green). Once removed, cover the area with a clean towel so no dust can enter the opening.
7. Clean the TB:
Use a cleaner made specifically for the throttle body. Spray it from all sides, and allow the cleaner to work for a minute or so. Wipe it clean with an old lint free cloth. If needed, use an old toothbrush to remove all of the build up. NOTE: It is OK to move the butterfly (gently). Be sure to clean every side well. Allow it to dry before reassembly. This is also a good time to clean your MAF sensor: How to Inspect and Clean a Mass Air Flow Sensor (MAF)
8. Put it all back together:
Simply reverse the process. Bolt the TB back on, using a cross pattern (like mounting a tire). Plug in the elctrical connection to the TB. Attach the resonator, and be sure to plug the breather hose back in. Then put the engine cover on, and connect the battery.