jQuery not supported.



Found 9061 matches: start

Next

Re: Installing a Double DIN into a 2013 Silverado Advice Nee

... I will use. But I will use the same harness as you have. There are some YouTube videos on how to remove the dash around the head unit. You simply start at the upper right corner and pry off one step at a time with your hands. This applies if your deck is up high in the dash not low like the slt ...
by dbmachine
Today, 2:49am
 
Forum: Mobile Electronics
Topic: Installing a Double DIN into a 2013 Silverado Advice Needed
Replies: 82
Views: 6041

Re: 2010 silverado door lock

does anyone have a wiring diagram of the door so i can start tracing wires
by Sethorama
Today, 2:22am
 
Forum: Electrical
Topic: 2010 silverado door lock
Replies: 7
Views: 201
by SilveradoSierra.com
Today, 2:22am
 
Forum: Electrical
Topic: 2010 silverado door lock
Replies: 7
Views: 201

Re: ignition key lock cylinder

... to unlatch the lock cylinder out of housing through the very small hole on top. And youll have to put it in in the run position and move to start position with allen wrench in there and wiggle back and forth and slide out.
by masterem88
Today, 1:26am
 
Forum: Interior
Topic: ignition key lock cylinder
Replies: 1
Views: 45

Re: New Sierra Owner

Very nice! Welcome indeed.

Yeah modding to make it your own will soon start!
by Centricity
Today, 1:18am
 
Forum: Member Introductions
Topic: New Sierra Owner
Replies: 11
Views: 122

Re: which one??

... months they'd be hollow and sound straight anyways. These trucks sound AMAZING straight. I found that out when I replaced my muffler and did the start up/rev video without a muffler. Mine sounds good at start up. Quiet at speed, but the lower RPMs when you're accelerating has a nice rumble. WOT ...
by dbrandt2009
Yesterday, 10:50pm
 
Forum: Exhaust
Topic: which one??
Replies: 10
Views: 171

Re: 99 NBS Crank/No Start and stalling - looking for suggest

Pump was changed, however loss of fuel pressure is suggesting a problem related to the pump. Did you eliminate the possibility of a wonky fuel pump relay? or a bad ground or connection to the pump? I picked up a new relay this afternoon, and stopped by the shop and swapped it out, as well as cleane...
by jackdanny
Yesterday, 10:48pm
 
Forum: Engine
Topic: 99 NBS Crank/No Start and stalling - looking for suggestions
Replies: 2
Views: 201

Re: Draining torque converter

... out converter fluid is to remove a cooler line easiest would be lower radiator line, and put a rubber hose over it and run it into a bucket and start up truck and let it run for about 10 seconds and start pouring new fluid into trans through dipstick tube. Keep noting approximately how much ...
by ASTE25
Yesterday, 8:19pm
 
Forum: Transmission/Drivetrain
Topic: Draining torque converter
Replies: 9
Views: 432

Re: Knock Senor Troubleshooting

It took me less then an hour to do my knock sensors, start to finish. I put a "V" of silicone in front of the knock sensor ports to give a path around the knock sensor.

Mudding will kill the sensors cause water gets trapped in the valley plate
by RIPPEDK20
Yesterday, 7:58pm
 
Forum: Vortec 5300 5.3L V8
Topic: Knock Senor Troubleshooting
Replies: 11
Views: 286

Re: Headlights not bright!

13rado wrote:did you wire in the relay? maybe your stock wiring isn't a fan of the HID's?

I did not but that would be a start at trying to figure out the problem. I may do that today, thanks.
by lanman38
Yesterday, 3:49pm
 
Forum: Electrical
Topic: Headlights not bright!
Replies: 12
Views: 305

Re: Addicted 2 GMC

WELCOME! Glad ya joined us. However, this site will not help cure your addiction issues. It will make it worse! There are so many great mods to do, you may have to hold on to your wallet everytime you surf the site! The 5100's and tires are a great start!
Enjoy!
by EKinMN
Yesterday, 1:34pm
 
Forum: Member Introductions
Topic: Addicted 2 GMC
Replies: 7
Views: 176
Next

More Results

Return to advanced search

It is currently May 20 2013, 7:38am

Login  •  Register
SHOP TALK (Live Chat)
Sitewide News Sitemaps & Feeds